Beta is moving toward the west near 2 mph (3 km/h), and a slow motion toward the west should continue into Sunday. This includes Baffin Bay, Corpus Christi Bay, Copano Bay, Aransas Bay, San Antonio Bay, Matagorda Bay, Galveston Bay, Sabine Lake, and Calcasieu Lake.Īt 100 PM CDT (1800 UTC), the center of Tropical Storm Beta was located near latitude 26.6 North, longitude 92.7 West. There’s also a storm surge watch in effect for Port Mansfield, Texas to Cameron, Louisiana. A tropical storm warning is in effect for Port Aransas to Intracoastal City, Louisiana. A tropical storm watch is in effect south of Port Aransas, Texas to the mouth of the Rio Grande, and east of Intracoastal City, Louisiana to Morgan City, Louisiana. The minimum central pressure was 994 mb or 29.36 inches.Ī hurricane watch has already been issued for the storm, extending from Port Aransas, Texas to High Island, Texas. update) and the movement was west or 270 degrees at 2 mph. The maximum sustained winds were 60 mph (the same as the 1 a.m. Central report for September 19 that Beta was at 26.6 N and 92.7 W, about 305 miles east-southeast of Corpus Christi, Texas and about 245 miles south of Lake Charles, Louisiana.
MPX - Chanhassen Township/Minn-St.The National Hurricane Center noted in its 1 p.m.HNX - Hanford AP/San Joaquin Valley, CA.GSP - Greenville/Spartanburg (Greer), SC.EWX - New Braunfels AP/Austin-San Ant, TX.CCX - Moshannon St Forest/State College, PA.The paths to the RIDGE legend overlays are. The paths to the NWS severe weather warnings overlays are. The paths to the RIDGE graphics/images are. The filename format for these recent images is: xxx_YYYYMMDD_hhmm_N?.gif, where For example, the most recent radar image for the Fort Worth Doppler radar is. For the radar image, legend, or warnings images, the most recent graphic available ends in "_0.gif". The table (below) provides the paths to each image. All RIDGE radar images are downloadable and all that is needed is the URL. This saves the steps needed to stack the images onto of each other in a graphics program and is also how all the RIDGE images used in this section were obtained. Use the toggle overlays to configure the image then use a screen capture utility to save the image to the local computer. Remember, this only saves the right-most image as indicated by the toggle bar. Use the overlay toggles and "right click" on each layer to save it to the local computer. The "Highways", "Topo", "Counties", "Rivers", and "Cities" overlays only needed to be downloaded once.Īt present, there are three ways to obtain images from the RIDGE radar. (The topography image is a compressed jpeg image.) To reproduce the RIDGE radar image, each layer needs to be captured and stacked on top of each other.īut it is not as bad as it sounds as fortunately, for any one radar site, once a copy of the overlays are obtained, only the radar image and the "Warnings" and "Legend" overlays change.
Except for the topography, these images are a "gif" format with a white background that has been made transparent. In this case it is "Cities".Ī typical RIDGE radar view is comprised of seven individual images layered on top of each other through the use of style sheets. The right most overlay selected is the top image. In the toggle overlay example (below), the "Cities" overlay is the top graphic and the only one that can be saved by selecting the image. Trying to save the RIDGE image will only save the legend graphic. In the example above, the "Legend" graphic is the top image selected. In the toggle overlay section, just below the radar image, the right most selected overlay is the top image. Unlike the old radar display, "right clicking" on a RIDGE radar image will only allow you to copy or "save to the clipboard" the very top layer, based upon the selected overlays.
0 kommentar(er)
